Avago（发音为a-va’-go） Technologies拥有5,500多种系列产品，主要应用于无线和有线通信、工业、汽车、消费
电子及存储和计算机等广阔的应用领域和终端市场。它在光电
耦合器、红外线收发器、光通信器件、打印机ASIC、光学鼠标
传感器和运动控制编码器等领域据称一直保持市场前3名的领导地位。Avago的产品通过代理商网络和直销队伍销售给40,000多家客户。
Avago 公司的MGA-231T6 是（0.9-3.5）GHz GPS//ISM/WiMAX低噪音
放大器">低噪音放大器（LNA），采用GaAs 增强模式pHEMT工艺，具有高增益。低噪音和高线性特性，工作定压可低至1.8V,主要用作GPS, WLAN 和WIMAX低噪音放大器。本文介绍了MGA-231T6主要特性， 演示板，应用电路和所用元件表以及S参数测量参考平面。
Avago Technologies’ MGA-231T6 is a low-noise amplifier （LNA） designed for GPS/ISM/Wimax applications in the （0.9-3.5）GHz frequency range. The LNA uses Avago Tech-nologies’ proprietary GaAs Enhancement-mode pHEMT process to achieve high gain with very low noise figure and high linearity. Noise figure distribution is very tightly controlled. A CMOS-compatible shutdown pin is included either for turning the LNA on/off or for current adjust-ment.
The low noise figure and high gain, coupled with low cur-rent consumption make it suitable for use in critical low-power GPS applications or during low-battery situations.
MGA-231T6主要特性：
Very Low Noise Figure
High Gain and Linearity
Low External Component Count
Low Shutdown Current
CMOS compatible shutdown pin （SD） current @ Vsd= 1.8V : 0.11mA
Useable down to 1.8V supply
Adjustable current via single external resistor/voltage
Small package dimension: 2.0（L）x1.3（W）x0.4（H） mm Specifications （Typical performance @ 25°C） At 1.575GHz
Vdd = 2.85V, Vsd = 1.8V, Idd =4mA
– Gain = 17.1 dB
– NF = 1.06 dB
– Input IP3 = 0.2 dBm
– Input P1dB = 7.7 dBm
MGA-231T6应用：
LNA for GPS, WLAN and WIMAX
图1.MGA-231T6演示板和应用电路元件表
Notes:
1. Pin 4 must be left unconnected
2. L3 and L4 form the input matching network. C2 and L2 form a matching network at the output of the LNA.
3. L1 and R1 isolates the demoboard from external disturbances during measurement. It is not needed in actual application. Likewise, C1 and C3 mitigate the effect of external noise pickup on the Vdd and SD lines respectively. These components are not required in actual operation.
4. Bias control is achieved by either varying the SD voltage with/without R2, or fixing the SD voltage to Vdd and adjusting R2 for the desired current. R2 = 8.2 kOhm will result in 4mA when Vdd = 2.85V, Vsd = 1.8V or Vdd = 1.8V, Vsd = 2.6V. R2 = 5.6 kOhm will result in 6mA when Vdd = Vsd = 2.7V.
图2.MGA-231T6演示板和应用电路图
图3.MGA-231T6 S参数测量参考平面
详情请见：
https://www.avagotech.com/docs/AV02-2212EN
