图文详情
产品属性
相关推荐
体积电阻率表面电阻率测试仪
数字*阻、微电流测量仪 型号:*T-121:体积电阻率测试仪,表面电阻率测试仪,固体*缘材料测电阻测试仪,微电流测试仪 用途:仪器仪表检测试验
体积小、重量轻、准确度高
电阻、电流双显示
性能好稳定、读数方便
*测试电压(10/50/100/250/500/1000V) 测试时电阻结果直读,免去老式高阻计在不同测试电压下或不同量程时要乘以系数等使用不便的麻烦, 使测量*电阻就如用万用表测量普通电阻样简便。
既能测*电阻又能测微电流
仪**合并**标准GB1410《固体电工*缘材料*缘电阻、体积电阻系数和表面电阻试验方法》和美国标准ASTM D257《*缘材料的直流电阻或电导试验方法》等标准的要求。
二、体积电阻率表面电阻率测试仪主要特点
电阻测量范围宽 0.01×104Ω ~1×1018 Ω
电流测量范围为 2×10-4A ~1×10-16A
典型应用
1.测量*静电鞋、导电鞋的电阻值
2、测量*静电材料的电阻及电阻率
3、测量计算机房用活动地板的系统电阻值
4、测量*缘材料电阻(率)
5、光电二*管暗电流测量
6、物理,光学和材料研究
四、体积电阻率表面电阻率测试仪技术指标
1.电阻测量范围: 0.01×104Ω ~1×1018Ω。
2.电流测量范围为: 2×10-4A~1×10-16A
3. 双表头显示: 3.1/2位LED显示
4. 内置测试电压: 10V、50V、100V、250、500、1000V
5. 基本准确度:1% (*注)
6 使用环境: 温度:0℃~40℃,相对湿度<80%
7 机内测试电压: 10/50/100/250/500/1000V 任意切换
8.供电形式: AC 220V,50HZ,功耗约5W
标准配置:
1.测试仪器:1台
2.电源线:1条
3.测量线:3根(屏蔽线、测试接线、接地线)
4.使用说明书:1份
其它可选配件:
本仪器配不同的测量电*(夹具)可以测量不同材料不(固体、粉体或液体)的体积电阻率和表面电阻率或电导率,
**合或**标准GB1410-89固体电工*缘材料*缘电阻、体积电阻系数和表面电阻试验方法,ASTM D257 *缘材料的直流电阻或电导试验方法 等标准要求。
表面电阻和体积电阻测试电*(三电*) 屏蔽箱
北广公司其它*缘材料检测仪器:
BDJC-0-100KV 介电击穿试验仪
BDJC系列*缘材料工频率介电击穿试验仪
BDJC系列电压介电强度试验仪器
BDJC系列 电压击穿试验仪
BDJC系列*缘漆漆膜击穿强度试验仪
BDJC电容器纸工频电压击穿试验仪
*T-121 体积表面电阻率测定仪
GDAT-A介质损耗测试仪/介电常数测试仪
GDAT-C新型介电常数介质损耗测试仪
BDH 耐漏电起痕试验仪
BDH-B耐电弧试验仪
中国检测行业与验证服务的*者和智领者,帮助众多检测质检单位和学校教研单位提供*的*质量解决方案。
注重每一个细节是北广公司对于每个客户的* , 也是北广公司一直追求的宗旨。北京北广精仪仪器设备有限公司 www.beiguangjy.com
Volume resistivity of surface resistivity tester
Di*al high resistance, a current measuring instrument t*e: *T-121: volume resistivity, surface resistivity uses: Instrumentation Test
One, volume resistivity surface resistivity tester overview
This instrument can measure high resistance, and measuring current. The American company Intel large scale integrated circuit and patented technology, the instrument has the advantages of *all volume, light weight, high accuracy. Dual 3.1/2 di*al display the resistance high resistance meter and current. Limit from 1× 104 Ω~ 1× 1018 Ω, is currently the most wide measurement range, the most accurate di*al ultra high resistance meter. Current measurement range of 2× 10-4 ~ 1× 10-16A. The built-in test voltage is 10/50/100/250/500/1000V adjustable. The instrument has the advantages of high precision, good stability, showing a rapid, easy reading, applied to anti-static products such as anti-static shoes, anti-static plastic rubber products, computer room anti-static floor activities such as the resistance value of the test as well as insulating materials electrical and electronic products insulation resistance measurement. The instrument can measure the resistance, and can directly measure the weak current.
Instrument is fully consistent with and better than the national standard GB1410 " solid electrical insulating materials, insulation resistance, volume resistivity and surface resistance test method " and " American Standard ASTM D257 DC resistance or conductance of insulating materials test methods " and other standards.
Two, volume resistivity surface resistivity tester main features
Resistance measuring range 0.01× 104 Ω~ 1× 1018 Ω
Current measurement range of 2× 10-4A ~ 1× 10-16A
Small volume, light weight, high accuracy
Resistance, current double display
Good performance is stable, easy reading
All the test voltage ( 10/50/100/250/500/1000V ) test resistance results in reading, is removed from the old high resistance meter in different test voltage or different scale should be multiplied by the coefficient of the inconvenient trouble, allowing the measurement of high resistance as the multimeter is used to measure the general resistance of samples is simple.
Not only can measure high resistance and micro current
Wide application: applied to anti-static products such as anti-static shoes, anti-static plastic rubber products, computer room anti-static floor activities such as resistance testing electrical and electronic products insulation resistance measurement
Three, volume resistivity surface resistivity tester technical indicators
The 1 resistor measurement range: 0.01× 104 Ω~ 1× 1018 Ω.
The 2 current measurement range : 2 × 10-4A~ 1 × 10-16A
3 double header display: 3.1/2 LED display
4 built-in test voltage: 10V, 50V, 100V, 250, 500, 1000V
5 basic accuracy: 1% ( note )
6: use environment temperature: 0℃ ~ 40 ℃, relative humidity <80%
7 built-in test voltage: 10/50/100/250/500/1000V arbitrary switching
The 8 power supply forms: AC 220V, 50HZ, power consumption is about 5W
Four, volume resistivity surface resistivity meter working principle
According to the Ohm's law, the measured resistance is equal to voltage is applied through Rx V divided by the current I. The traditional high resistance meter is the working principle of measuring voltage V fixed, by measuring the current flows through the sampling resistor I to get the value of resistance. From Ohm's law can be seen, because the current I is inversely proportional to the resistance, but not proportional to the resistance, so the display value is nonlinear, namely the resistance to infinity, the current is zero, i.e., zero is∞, in the vicinity of the scale is very dense, with a low resolution. The scale is nonlinear. Because the measurement of different resistance, the voltage V also vary, so the average high resistance meter is poor accuracy, low resolution.
At the same time measure the voltage across the resistor V and the current through the resistor I, through the interior of the large scale integrated circuit to complete the voltage divided by the current calculation, and then the results obtained after A/D conversion to di*al show resistance, even if the voltage across the resistor V and the current through the resistor I is changed at the same time, the display resistance value is not as common due to high resistance meter that measured voltage or current change of V I change, so, even if the measured voltage, resistance, power supply voltage is measured the changes in the results have little effect, the measurement accuracy is very high ( patent ), theoretically the error can be zero, while the actual error can be done a few thousandths or extremely few.
T*ical application
1 measurements of anti-static shoes, conductive shoes resistance value
2, measurement of the antistatic material resistance and resistivity
3, measurement computer room with movable floor system resistance
4, measurement of insulation resistance ( rate)
5, photodiode dark current measurement
6, physics, optics and materials research
Canton company other insulating materials testing instruments:
BDJC-0-100KV dielectric breakdown testing instrument
BDJC series insulating materials at power frequencies of dielectric breakdown test instrument
BDJC series voltage dielectric strength test apparatus
BDJC series voltage breakdown testing instrument
BDJC series insulating paint film breakdown strength tester
BDJC capacitor voltage breakdown testing instrument
*T-121 volume surface resistivity measuring instrument
GDAT-A dielectric loss tester / dielectric constant test
GDAT-C model dielectric constant dielectric loss tester
BDH leakage resistance tester
BDH-B arc resistance tester
China Inspection and certification services tip and intellectual leader, helped many testing quality inspection units and schools and research units to provide comprehensive one-s* quality solutions.
Pay attention to every detail is Canton company for each customer commitment, and North Canton company has been pursuing the aim of. Beijing North Canton precision instrument equipment limited www.beiguangjy.com
est-121
北广精仪仪器