LED后备电源

 一：主要技术指标
Technical indexes

输入电压:85-265V交流
Input voltage: 85-268VAC
输入电流:0.3A
Input current: 0.3A
输出电压:DC36V
Output voltage:DC36V
输出电流:830MA
Output current:830MA
输出功率:30W
Output power:30W
电源效率:≥88%
Power factor:≥88%
电池转换效率:≥96%
Battery conversion efficiency:≥96%
停电后30W日光灯可连续工作4小时
30w tube light Can still work 4 hours after power out.

二：主要性能
Performance

本产品适用宽电压输入，在任何地区都可以使用。
This product is suitable for wide voltage input, can be used anywhere.

智能充电。本产品采用*的*芯片控制，能自动识别电池特性而采取相应的充电方式。
Intelligent charging. This product adopts advanced special chip to control, can automatically identify battery characteristics and take corresponding charge method.

3.多用途。本产品可作一般照明灯具使用，也可作应急照明灯使用，只要一个开关就可以控制。
3.Multi-purpose. This product can be used as general lighting ,but also can be used as emergency lighting, just need a switch to control.

4.方便性。本产品安装使用都*方便。如固定使用，在不改动任何线路的情况下，就可以实现该产品的*功能。当普通照明时，采用了遥控开关来控制灯具的开关。如移动使用时，则可以直接使用该产品上的自带的电源开关控制。
4.Convenience. Easy to install and use. When fixed use, it can realize all the functions without changes any circuit.When general lighting, using the remote switch to control the light on/off. When move use, can directly use the power switch control which the products owned.

5.消*模式。将面板上右边消*模式打开，就可以实现传统消*灯的功能。
5. Fire mode. Open the fire mode which on the right of panel.then can realize the function of the traditional fire light

三：产品功能介绍
    Product function
如下图所示
As shown in the following picture

1.指示灯部分：电源指示、充电指示、充满指示、工作指示、对码指示。①市电：绿色指示灯，此指示灯亮时，表示市电正常。②充电：当检测到产品内置电池电压不够时，灯具内的电路自动给电池充电，当电池处于充电状态时，红色指示灯发亮；当电池充满电时，红色充电指示灯熄灭，绿色指示灯亮；充满电后电路自动转入涓流浮充状态，延长了LED消*应急照明灯灯具的使用寿命。
1.Indicator Light parts: the power indicator, charging indicator, full of instructions, work instructions, code instructions. the mains-green light.When the light is on, it means the mains is normal. ②the charge: when detect by the built-in battery voltage is not enough, the circuit to be automatic to recharge the battery, when the battery in charging state,the red indicator lights,when the battery fully charged , the red indicator goes out ,the green indicator lights ;After fully charged the circuit will automatically transfer to trickle floating state,which can extend the life of LED fire emergency lamps.

2.按钮开关部分：①对码。是指遥控开关学习的功能，如用户遥控器没有问题则无需按动。（另附学习功能介绍）②效验。是在任何情况下，按动此开关来试验电池是否能正常工作的一个开关。③常开开关。是本产品附带的一个开关，主要是在移动工作时当照明开关使用，使用遥控开关时则关掉此开关。④消*模式开关。此开关开时本产品可当消*应急灯使用，即有电时灯不亮，停电后灯亮。此开关关掉时，当普通灯具使用。
2.Push button switch parts: ①Code button. It is function of remote control switch learning, it need’t to press with the control no problem. (attachment is introduction of learning function)    ②Test button. In any case, press the switch to test the battery can work or not. ③Normally open switch. It is an appendant switch and mainly to use lighting switch when product move work ,but turn off this switch when use the remote control switch. ④Fire mode switch. It can be used as fire emergency light when open the switch,that is,when have power it not lights,no power it lights. It used as ordinary lamps when the switch turn off.

3.电源开关。此开关在本产品的后面，如长期不用则要关断此开关，但为了保护电池的使用寿命，三个月内*要进行一次充放电过程。
3.Power switch. It is on the back of product, please turn off the switch if long-term don't use, but in order to protect the life of the battery, it must be conduct a charge and discharge process one time in three months

4.36VDC输出插座。如使用我司配套的灯具，*要直接将灯具上的插头*此插座即可。如用户需要使用自己准备的灯具，则要注意正负*性。
4.36 VDC output socket. If use the lamps form a complete set by our company . only need to let plug into the plug direct . If use the lamps by your side , should be pay attention to positive and negative polarity.

5.扩充插座。此为四针插座，左边二针为外接电源，如太阳能板高容量电池，右边二针为外置开关插座，供*场合使用。
5.Expansion socket. It is four needles socket, the left two needle for external power supply, such as solar panels high capacity battery, the right two needle for external switch socket, use for special occasions.

四：指示灯、按钮、船型开关各功能说明
The function declaration of indicator light, button, ship t*e switch

1.电源指示灯：当市电正常时，此灯亮
1.The power indicator light: when the mains normal, it lights.

2.充电指示灯：当电瓶亏电，在充电时，此指示灯亮。电池在*没有电的情况下，打开电源开关通电后，充电电路开始进入自动检测电池电量来识别所需的电池电流，此时充电指示灯红、绿都亮；然后进入充电慢充状态，电流为200mA（有利于保护电池使用寿命），此时红灯亮，绿灯熄灭。当电池电压*电池的电压75%时，转入快充状态，电流为1.2A。当电池电压充到电池的95%时，进入慢充阶段，此时红灯、绿灯同时闪烁。*后进入结束状态，当电池电量是100%时，红灯灭，绿灯亮。充电电源即进入关闭输入电流。
2.Charging indicator light: when the battery power in charge, the indicator lamp light. When the battery no electric power totally , open the power switch to power on, charging circuit begin to enter the automatic detection of the battery power to identify the battery current, and the red&green indicator are light ; And then into the slow charging state, the current is 200 mA (help to protect the battery life), at this time the red one light, the green one go out. When the battery voltage reach to 75%, then into the fast charging status, current is 1.2 A. When the battery voltage reach to 95%, into the slow charging stage, the red light and green light flashing at the same time. Finally into the end state, when the battery power is 100%, the red light, the green go out. Charging power is shut down into the input current.

3.充满指示灯：当电瓶充满后，此指示灯亮。
3.Full of light indicator: When the battery is full charged, this indicator lights.

4.工作消*指示灯：此等有两个功能。当此指示灯亮时，表示有电压输出，在没接LED灯时，请注意输出端尽量不要短路，在接灯管时，请关掉此灯。若消*模式开关打开，无论有无输出，此灯常亮，表示消*模式已开启。
4.Work fire indicator light: these are two functions. When this indicator lights, means voltage output, and please pay attention to the output end do not short circuit when without connect LED lamps.please turn off the light when connect tube. If the fire mode switch on, no matter whether have output, the lamp always lights,It means the fire mode is open.

对码指示灯：对码。在遥控器遗失或更换时需要配合对码按钮进行对码。
5.Code indicator light: the code.It is needs to cooperate to code button for code when the remote control lost or replace.

6.灯具开关：此开关为本品直接控制开关。在不用遥控开关时，此开关可直接控制灯具的开关，当开关在开启状态时，遥控开关无效。
6.Lamps switch: it is for the product direct control . Can directly control the switch of lamps without use remote control switch .The remote control switch is invalid when the switch in open sate.

消*模式开关：当此开关打开时，为消*模式。即市电正常时，灯不亮，停电后，灯自动亮。
7.Fire mode switch: it is fire mode when the switch is open. That is the mains is normal, the lamp lights, power off, the lamp not lights.

8.电源开关：此开关为本机总开关，同时控制高压交流与电瓶直流的电路开关。（说明：本机*开关在“—”为开，在“0”为关。）
Power switch: It is master switch, and                                                                                                                                                control of High-voltage AC and battery DC. (note: all switch in the "—" for open, in the "0" for close.

9.遥控器：遥控器为本机身配的，非接触式灯具开关，*具备开关灯具功能。当机身灯具开关处于“开”状态时，遥控器工作无效，可控*距离为50米。
Remote control:work for this product only, non-contact lamp switch, only have switch function of lamps.When the lamps switch in the "open" state, the remote control work is invalid,controllable the range for fifty meters.

五：保养与维护
Care and maintenance

如长时间不使用，应关闭后面的电源开关。请勿在雨水湿度大于或等于90％的环境、有腐蚀性的环境下使用。
For a long time without use, should shut down the back of the power switch. Please do not
use in the rain humidity ≥90% , corrosive environment .
   
六：注意事项
    Notice
在使用本灯具之前，*须详细阅读相对应的消*应急灯的说明书，方可接上交流电源对消*应急灯进行充电；
1. Before use of the lamps , must read the corresponding fire emergency light specifications, and then charging for fire emergency light with the AC power supply .

本灯具采用胶体电瓶组，LED消*应急灯在出厂之时，电池处于放空状态，使用前应先对消*应急灯充电约18小时；
2.The lamps use colloid battery group, it should be charging about eighteen hours before use.

3.当需要更换LED消*应急灯的光源时，*须和本公司所提供的规格和参数一致的光源替换，勿用劣质光源；
3.When need to replace the light source of the LED fire emergency lamp ,must use the exact same light source to replace, do not use inferior light source.

4.长时间搁置不用会影响电池的寿命，建议每隔三个月放充电一次，在正常使用中应每隔六个月进行一次放电操作，当放电时间少于额定时间的30%时，须更换电池，更换电池时请注意电池的型号*性，电压容量。
4.Long time lay up will affect the battery life, it is suggest charging and discharging one time per three months , in normal use should discharge one time per six months, when the discharge time is less than 30% of rated time, should replace the battery and please pay attention to the battery model polarity, voltage capacity

5.本产品免费*一年，一年后有偿维修服务。注意：一旦自行拆开机壳，将终止保修。
5.This product free warranty for a year, a year later service with paid . Note: once di*antled by your side , will terminate the warranty.

                             本说明的解释权归本公司*，如有变更怨不另行通知
       The interpretation right of the instruction owns to our company , change without notice .