供应U-MULTILINK Multilink Universal 仿真器

Multilink Universal 多合一开发接口

U-MULTILINK 

特性:

• 从PC到Multilink的USB接口允许快速，方便的编程和调试--通过方便和兼容的USB接口。
• USB供电 -无需单独的电源供应(目标烧写小于1mA)。
• 目标电压：1.6V的-5.25V
• 目标频率：16KHz-50MHz (适用于HCS08，RS08，CFV1，或HCS12X)
• 支持 HCS08，RS08，HCS12，HC12，ColdFire V1/+V1，ColdFire V2-4，Qorivva MPC55xx/56xx，以及 Kinetis ARM 微处理器系列。
• 自动频率检测+适应，用于HCS08设备。
• 自动频率检测，用于HC(S)12(X)设备。
• 对RS08设备在RESET line生成烧写电压

P&E’s USB Multilink Universal is an all-in-one development interface which allows a PC access to the Background Debug Mode (BDM) or JTAG interface on Freescale HCS08, HC(S)12(X), S12Z, RS08, ColdFire V1/+V1, ColdFire V2-4*, Qorivva 55xx/56xx, and Kinetis ARM microcontrollers. It connects between a USB port on a Windows machine and the standard debug connector on the target. The Freescale microcontrollers are supported via the multiple headers located on the USB Multilink Universal. The product photos to the left of this page show how the headers can be accessed by simply flipping open the plastic case. Ribbon cables suitable for a variety of architectures are included.

Supported Freescale Devices:

• Kinetis
• Qorivva MPC55xx/56xx
• ColdFire +V1/ColdFire V1
• ColdFire V2/3/4
• Power Architecture PX Series
• HC(S)12(X)
• S12Z
• HCS08
• RS08
• DSC

By using the USB Multilink Universal, the user can take advantage of the background debug mode to halt normal processor execution and use a PC to control the processor. The user can then directly control the target’s execution, read/write registers and memory values, debug code on the processor, and program internal or external FLASH memory devices.

The USB Multilink Universal works with P&E Microcomputer System's in-circuit debuggers and flash programmers to allow debug and flash programming of the target processor. For many of the supported processors, P&E has a set of interface libraries allowing the user to write their own Windows based application which interacts with P&E's debug interface. IAR, Codesourcery, Keil, and CodeWarrior software all support the use of P&E's USB Multilink Universal to develop and debug with Freescale's Kinetis ARM devices.

This interface is USB 2.0 compatible, and it is also backwards compatible with USB 1.1 ports.

NOTE: For a much faster all-in-one development interface which can also supply power to the target, please see the USB Multilink Universal FX.

For production usage, see either the Cyclone PRO or Cyclone MAX stand alone programmer and debug interface, depending on which processor you are working with. See the comparison chart below.

FEATURES:

• USB interface from PC to Multilink allows for fast, easy programming and debugging -- with the ease and compatibility of the USB interface.
• Draws power from USB interface-- no separate power supply required (draws less than 1mA from the target).
• Target Voltage: 1.6V-5.25V
• Target Frequency: 16Khz-50Mhz (applies to HCS08,RS08,CFV1, S12Z, or HCS12X only)
• Compatible with HCS08, RS08, HC(S)12(X), S12Z, ColdFire V1/+V1, ColdFire V2-4, Qorivva MPC55xx/56xx, and Kinetis ARM families of microcontrollers.
• Includes USB cable, Type A Male to Type B Male, 6-ft.
• Auto-frequency detection + trimming capabilities for HCS08 devices.
• Auto-frequency detection for HC(S)12(X) devices.
• Generates programming voltage on RESET line for RS08 devices.

Includes:

• One (1) USB 2.0 High Speed Cable, Type A to Type B, 6-ft.
• One (1) 6-pin 0.100" pitch ribbon cable for connecting to RS08, HCS08, HC(S)12(X), S12Z, ColdFire V1/V1+ targets
• One (1) 14-pin 0.100" pitch ribbon cable for connecting to Qorivva MPC55xx/56xx targets
• One (1) 26-pin 0.100" pitch ribbon cable for connecting to asynchronous ColdFire V2/V3/V4 targets
• One (1) 20-pin 0.100" pitch ribbon cable for connecting to Kinetis ARM targets
• One (1) 20-pin 0.050" pitch ribbon cable for connecting to Kinetis ARM targets