公母排插、车载DVD翻板插座，板对板连接器，浮动插座，10P公座

*

测试项目

Test Item

试验方法及条件

(Test Condition & Method)

规格Standard

6.1

接触阻*contact impedance

公座和母座导体之间的接触电阻(Measured the resistance of mated Pin Header )

30毫欧以下

(below 30mΩ)

6.2

*缘阻*insulation impedance

在端子之间和端子与壳之间加DC500V条件下持续1分钟测量among terminals or between terminal and shell, under condition  of DC500V ,last 1min to test

1000兆欧以上

（ above100MΩ）

6.3

耐电压disruptive test

在端子之间和端子与壳之间加AC 500V(50H或60H)条件下持续1分钟测量among terminals or between terminals and shell, under condition of AC 500V(50H or 60H),last 1min to test

无击穿现象出现

（ without disruptive ）

*

测试项目

Test Item

试验方法及条件

(Test Condition & Method)

规格Standard

7.1

*力与拔出力度insert and pull out

用配套插头*插座再从中拔出;测量*和拔出的作用力make the the force of insert the socket and pullout

*力度:0.7Kgfmax insert force: 0.7Kgf MAX

拔出力度:0.3Kgf-2.6Kgf pullout force : 0.3Kgf to 2.6 Kgf

7.2

端子强度 terminal strength

顺端*力方向施加500g力条件下持续10秒 add 0.5Kgf along the terminal spring , last 10 seconds

未有裂纹与失去弹性 wiouth fault trace, still with elastic sensation

*

测试项目

Test Item

试验方法及条件

(Test Condition & Method)

规格Standard

8.1

*试验 hight temperature resistance test

在环境中放96小时,再放在正常环境中30分钟后进行测试Test after lasting 96hours under 90&plu*n;2°C,and then staying 30mins under normal environment

1. *迹象显示机械及电气性能损坏（mechanical characteristic &electrical characteristic are well  ）

8.2

耐低温试验 low temperature resistance test

在-20&plu*n;3°C环境中放96小时,再放在正常环境中30分钟后进行测试Test after lasting 96hours under -20&plu*n;3°C,and then staying 30mins under normal environment

8.3

盐雾试验salt spray test

把试验样品从试验箱悬挂起来,采用浓度为(5&plu*n;0.1)%(质量百分比)的氯化纳溶液连续雾化16小时,试验后用流动的蒸溜水轻轻洗去表面沉积物,在常温条件下恢复1-2小时hang up the sample for 16hours in the test box of (5&plu*n;0.1)%(m* percent) NaCl solution, after that flush away the surfacial deposit lightly with running distilled water; finally, under normal environment, make it lay 1-2 hours

外观*伤

(五金件应无露出底金属的严重锈蚀,使用预定好的型材,其落料而允许有不影响其性能的轻微腐蚀) 

the sample apperance surface is well, non-corroded.(the inside metal of the metal part isn’t badly corroded, slight corrode is possible ,but it doesn’t influence the character.

*

测试项目

Test Item

试验方法及条件

(Test Condition & Method)

规格Standard

9.1

可焊性试验 weldability test

将端子顶部浸入焊锡池2MM深;温度270&plu*n;5°C;时间2&plu*n;0.5秒 infusion the terminal * into soldering acid 2M deep; termperature: 270&plu*n;5°C ;duraton: 2&plu*n;0.5 seconds

浸入部分90%以上表面被锡覆盖 90% of the part infused is plating by tin

9.2

寿命试验life testing

在无负荷条件下以每分钟15-18次的速度操作10000次 under unloaded condition ,working ten thousand times at the speed of 15-18 times per min

1. 接触阻*150毫欧，变化范围初始值(30%)contact resistance < 150mΩ>，variation range initial value(30%)