LED驱动电源

Model

JL-020-1216

JL-020-2483

JL-020-3260

JL-020-1641

OUTPTU

DC VOLTAGE

12V

24V

32V

48V

LED OPERATION VOLTAGE Note.5

9-12V

18-24V

28-32V

36-48V

RATED CURRENT

1600mA

830mA

625mA

410mA

CURRENTRANGE

0.0-1600mA

0.0-830mA

0.0-625mA

0.0-400mA

RATED POWER

20.2W

20.0W

20.0W

20.0W

RIPPLE & *ISENote.2

<360mVpp

< 360mVpp

< 480mVpp

< 450mVpp

VOLTAGE TOLERANCENote.3

&plu*n;5%

CURRENT ACCURACY

&plu*n;5%

LINE REGULATION

&plu*n;1%

LOAD REGULATION

&plu*n;2%

SETUP ,RISE TIME

3000mS 180mS/230VAC 3000mS 150mS/115VAC（Full Load）

INPUT

VOLTAGERANGE

90~270VAC OR 126~380VDC

FREQUENCYRANGE

47~63Hz

POWER FA*OR（T*.）

PF > 0.9（Full Load）

EFFICIENCY (T*.)

80%

AC CURRENT (T*.)

0.088A/115VAC 0.046A/230VAC

INRUSH CURRENT (T*.)

40A/230VAC

LEAKAGE CURRENT

<0.5mA 240VAC

PROTE*ION

OVER VOLTAGE

14 ~ 16V

27 ~ 34V

36 ~ 48V

SHORT CIRCUIT

Hiccup mode, recovers automatically after fault condition is removed

ENVIRONMENT

WORKING TEMP。，HUMIDITY

0~40℃，20~90% RH. *N-CONDENSING

STORAGE TEMP., HUMIDITY

－20~70℃，15~95% RH. *N-CONDENSING

TEMP. COEFFICIENT

&plu*n;0.03%/℃（0~40℃）

VIBRATION

10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes

SAFETY &

EMC

SAFETY STANDARDS

TUV EN61347-1, EN61347-2-13, UL8750,CSA C22.2 No. 250.0-08 approved

WITHSTAND VOLTAGE

Primary To secondary：3750VAC 10mA 1 minute

ISOLATION R*ISTANCE

I/P-O/P:100M Ohms / 500VDC / 25℃/ 70% RH

EMI CONDU*ION & RADIATION

Compliance to EN55015, EN61000-3-2 Cl* C( 75% load); EN61000-3-3

EMSIMMUNITY

Compliance to EN61000-4-2,3,4,5,6,8,11, EN61547, criteria A

OTHERS

MTBF

643.6Khrs min. MIL-HDBK-217F (25℃)

DIMENSION

44.6mmx 20.2mm x 12mm

PACKING

0.04Kg200Pcs/9.2Kg

*TE

1. All parameters *T specially mentioned are measured at 230VAC input, rated load and 25℃of ambient temperature.

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

3. Tolerance : includes set up tolerance, line regulation and load regulation.

4. Derating may be needed under low input voltage. Please check the static characteristics for more details.

5. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.

6. Length of set up time is measured at first cold start. Turning ON/OFF the power supply may lead to increase of the set up time.

7. In the European market this power supply can be used for LED lighting applications with input power up to 25W.

8. Suitable for indoor use or outdoor use without direct sunlight exposure. Please avoid immerse in the water over 30 minute.